Tuniq Ripper 1000W Power Supply - Info, Features and Specifications

Article Index
Tuniq Ripper 1000W Power Supply
Info, Features and Specifications
Inside the PSU and Test Setup
Testing the 1kW Ripper PSU

Features & Specifications:

As of late there have been a few companies that have branded their PSUs with "SLI Certified" logos that weren't actually certified.  We decided to see if this feature was accurate so we went over to the SLI Zone and were not able to find the Tuniq Ripper 1000W PSU in any list for any SLI setups.  I've questioned Tuniq regarding this before and they state that NVIDIA is slow to update their list.  That being said, the Tuniq Ripper 1000W PSU doesn't officially claim to be "SLI Certified" - at least not on the box and while I'm sure it will indeed run three graphics cards as stated, those who live by "Certified" products may want to wait until it shows up in the list - or look at the 950W Miniplant.

PSU Label
PSU Label

 

The values on the label look pretty good and Tuniq appears to be quite conservative with their "Total Power" rating based on the amperage available to each rail.  Simple math says that the 3.3v and 5v rails should actually be capable of 242.4W.  The combined wattage of all four +12v rails is 1200W max and the -12v and +5vsb is 24.6W.  Total max output is theoretically 1467W, and the conservative 1000W rating of the entire unit should be pretty accurate.  Tuniq has rated this PSU at 80 PLUS efficiency, and it should run nice and cool without any issues delivering the rated output.


Features:

  • 80 PLUS Bronze Certified
  • SLI Certified
  • Support three way SLI
  • Active PFC
  • Advanced Off-Line Cooling (Allow Power Supply fan continue cooling for 120 seconds after shutdown. Provide advanced cooling and extend Power Supply, hardware/component lifetime.)
  • Full Circuit Protection (OCP/UVP/OVP/SCP/OLP)
  • Silent 140mm Two-Ball Fan
  • 3-year Warranty
  • Size : 160x150x86mm

 

As mentioned above, one of the interesting features of the Tuniq Ripper 1kW PSU is the Fan Delay-Off Function.  The idea with this 2 minute fan delay is that the fan can cool down the hot components inside the PSU as there is often a rise in temperature immediately following a system shutdown.  This fan delay helps protect your PSU from this overheating.  In reality, I don't think this is really a necessary feature, but I know of some extreme overclockers who swear by this principle.

SPECIFICATIONS

Product Number

PSU-RIP1000-BK

Power

1000W

Dimension

160mm(L) x 150mm(W) x 86mm(H)

Switches

ATX Logic on-off additional power rocker switch

Power Factor

PF > 0.95

Cooling System

140mm Fan, 1900RPM±10%

Noise

27 dBA at 1300RPM

Efficiency

Up to 80%

Hold-up Time

16 ms

INPUT

Input Voltage

100-240VAC

Input Frequency Range

47~63Hz

MTBF

100,000 hrs minimum (at 25℃)

Input Current

100Vac/13A max

OUTPUT

 

Max/Min

Regulation *1

Ripple & Noise *2

Output

+5V

30A/0.2A

±5%

70mV/100mV

180W

+3.3V

28A/0.1A

±5%

70mV/100mV

+12V1

20A/0.1A

±5%

120mV/200mV

900W

+12V2

20A/0.5A

±5%

120mV/200mV

+12V3

30A/0A

±5%

120mV/200mV

+12V4

30A/0A

±5%

120mV/200mV

-12V

0.8A/0A

±10%

150mV/200mV

9.6W

+5Vsb

3.0A/0.1A

±5%

70mV/100mV

15W

Total Power

1000W

+5Vsb' operate at 3.0A max load base on PS-ON mode.
If PS-OFF +5Vsb only operate at 3A max load.
Add 0.1µF capacitors across output terminal during ripple & noise test.

Fat Bunch Of Cables
Fat Bunch Of Cables 

 

 

Connectors:

1 * 20+4Pin Mainboard
6 * PCI Express (3 * 6Pin, 3 * 6+2Pin)
6 * 4Pin Molex
1 * 4Pin FDD
6 * SATA
1 * 8Pin EPS12V
1 * 4Pin P412V

 

Take a quick look at the cables below before we dive inside this PSU on the next page. 

24-Pin Cable
24-Pin Cable
 Molex Connectors
Molex Cables
   
SATA Cables
SATA Cables
 PCIe Cables
PCIe Cables